Loading...
Custom No-Velcro Sunbrella Over the top Enclosure 2

Custom No-Velcro Sunbrella Over the top Enclosure

CODE: c_no_velcro


List price: $494.00  

Price: $308.75

You save: $185.25 (38%)
-38%
  • 3 sided 
  • 2-sided w/ Cold Curtain & Club Protector  (+$187.00)
  • White 
  • Black 
  • Strap w/ Hook 
  • Snaps 

Note: Normal shipping time is approximately 3 weeks! Certain times of the year shipping can take up to 6 weeks.

 

Club Car DS models - Important, please read:
These enclosures are custom and it is very important that we know your cart model and the type of top. Club Car DS model changed tops in mid-year 2000. To determine whether you have a pre-2000-1/2 year or a 2000-1/2 and newer you can look for the following: The top frame for the pre-2000-1/2 will be aluminum in color and the 2000-1/2 and newer will be black in color; The seat backs for the pre-2000-1/2 will be two(2) separate backs and the 2000-1/2 and newer will be one (1) full back.

Club Car Precedent year models - Important, please read:
Club Car began producting the Precedent model in 2004 but the also still make the DS model mentioned above.


Ezgo RXV models - Important, please read:
These enclosures are custom and it is very important that we know your cart model and the type of top. Ezgo RXV model changed tops in early-year 2009. To determine whether you have a pre-early 2009 year or an early 2009 and newer you can look for the following: Grooves in the underside of the top- 6 grooves for pre-early 2009 or 5 grooves for early 2009 to present.  
Remove the windshield from your cart.

OPTIONS:

 3 sided:  2 sides w/ a rear curtain that is full length designed to cover the bag area with 2 standard size bags.   (Rolls up and snaps under the valance when not in use)

2-sided with Cold Curtain:  The cold curtain is a wrap around curtain for Club Car DS, Ezgo Marathon 86-93, and Ezgo TXT.  It is the ultra seal style for the Club Car Precedent.  The ultra seal is not pictured.

2-sided with Cold Curtain and Club Protector:  Covers both sides, also has Cold Curtain in back and allows Club Protector to be let down to protect bag area when needed.

 *All panels roll up and snap under the valance when not in use.

  •  Note that the entire enclosure must be a solid color except the valance.  The valance is the only part of the enclosure that can be a stripe but it can also be a solid color.

Custom made Sunbrella enclosures and seat covers are custom made for you at the time of order and returns are not accepted except for defects which will be fixed or replaced at the manufacturer's option. Please ensure you order for the right year and make of golf cart.



We also offer a 4-Passenger enclosure. Please call for more information or look at code # nv4pass3ssun.

 

Installation instructions for over the top enclosures

  1. Remove the windshield from your cart.  
  2. Install the enclosure assembly by laying it on the roof of the golf car, with the pocket toward the front of the golf car.  Pull the pocket of the enclosure out past the front edge of the roof.  Slide the enclosure toward the back of the car, allowing the roof of the golf car to slide into the pocket of the enclosure.  Lower the rear curtain and if it is the ultra seal cold curtain, tuck each side of the cold curtain under the seat.  Lower the side curtains and completely unzip and remove the sleeve portion of the front door of the enclosure.  Wrap the sleeve around the windshield frame so that the cut out for the windshield retention clip is toward the top end of the sleeve. Engage the smaller zipper so that it wraps snugly around the windshield frame. The zipper should be on the backside of the windshield frame.  Adjust the height of the sleeve as necessary for even alignment after the sides are installed and zipped to the sleeves. 
  3. Rear Bag Curtain or Ultra Seal Cold curtain:  Zip the rear curtain to the side curtains.  If you have a standard bag curtain without the RainGuard club protector go to step 5.  Attach the bottom center section of the ultra seal cold curtain to each end section and to the seat back using the Velcro strips.
  4. RainGuard club protector:  The RainGuard club protector rests on the front of the bag framework.  The front top of the RainGuard club protector is on the inside and under the back lip of the top. You will need to tilt the RainGuard forward slightly to get it under the top and then it will rest on the bag framework.  Bolt it to the framework using the bolts provided. 
  5. If your enclosure has body snaps install the male portion of the snaps onto the body of the cart using the pop rivets provided.  The enclosure should be snug but not to tight. 
  6. Re-installing your windshield:  If using a support bolt for the windshield, cut a small “X” in the sleeve to allow for placement of the support bolt through the windshield frame and sleeve.  Un-zip the sleeve to expose the back side of the windshield frame where the support bolt hole is.  Reverse the bolt by inserting it from the backside of the windshield frame.  Attach the windshield by carefully snapping the windshield extrusion around the sleeve and frame.  Attach the nut to the supporting bolt and tighten.  Re-zip the sleeve. 
Payment Options
Click here for BBB Business Review Check out with PayPal and choose PayPal Credit. Subject to credit approval. See Terms.

 Are you ready for the change of weather?  Do you need protection?  Come check out all the Golf Cart Enclosures we have for your cart.
Don't be left out in the weather without an enclosure for your cart.   See our line of long-lasting weather-resistant Sunbrella enclosures.

Enclosures